Trusted ac repair for Irving properties. Same-day service available, transparent pricing, and a workmanship guarantee.
KIC Refrigeration delivers expert air conditioning repair in Irving, TX, diagnosing compressor failures, refrigerant leaks, frozen evaporator coils, and electrical faults using superheat, subcooling, and amp draw measurements. Our EPA Section 608 certified technicians restore rated SEER output through manufacturer-guided repair procedures across all major AC brands.
Properties throughout Irving (pop. 258,636) face unique demands when it comes to ac repair. Texas heating loads, cooling calculations, and the insulation levels and duct configurations found in Irving homes all influence the approach we take. KIC Refrigeration tailors every ac repair project to the conditions your property actually faces — no generic solutions.
Choosing the right contractor for ac repair in Irving, TX makes all the difference between efficient comfort and a system that short-cycles. KIC Refrigeration uses Manual J load calculations, installs to manufacturer specifications, and backs every project with a warranty. Call (866) 858-2961 to schedule your free assessment.
From initial contact to final verification — here is how we handle ac repair.
Our Irving technician listens to your description of the problem, inspects the thermostat settings and wiring, checks the electrical disconnect and breaker, and performs a visual inspection of the outdoor condenser and indoor air handler for obvious issues like a frozen coil, tripped safety switch, or burned wiring.
KIC Refrigeration diagnoses AC failures in Irving, TX with precision electrical and refrigerant testing. We check capacitors within 6 percent of rated microfarads, measure contactor coil resistance, verify compressor winding resistance for shorts and opens, and test the refrigerant circuit — comparing suction pressure, discharge pressure, subcooling, and superheat to the manufacturer target values for the current outdoor ambient temperature.
We replace the failed component — capacitor, contactor, fan motor, compressor, or metering device — using parts rated for your system. For refrigerant leaks, we locate the leak, repair or replace the leaking component, evacuate, and recharge the system by weight.
Our Irving technician verifies the repair by running the AC through a full cooling cycle. We measure supply and return air temperatures at the air handler to confirm a 16 to 22 degree split, check that suction pressure produces 35 to 45 degree evaporator saturation temperature, and verify the system cycles cleanly on and off.
Transparent answers about ac repair from our certified technicians.
AC repair in Irving typically costs $150 to $500 for common component failures including run capacitors ($150 to $250), contactors ($150 to $350), condenser fan motors ($250 to $500), and blower motors ($300 to $600). Compressor replacement is the most expensive repair at $1,500 to $3,500 depending on unit tonnage and whether the system uses R-410A or older R-22 refrigerant. Evaporator coil replacement runs $800 to $2,500 including the refrigerant recovery and recharge. KIC Refrigeration provides a detailed written estimate with itemized parts and labor costs before beginning any AC repair at your Irving property so there are no surprises on the invoice.
The industry guideline is to repair if the unit is under 10 years old and the repair costs less than 50 percent of a new system. AC units over 15 years old — especially those running R-22 refrigerant — are almost always better replaced. R-22 has been phased out of production and the remaining supply costs $80 to $150 per pound, making even minor refrigerant leaks prohibitively expensive to fix. A new 16 SEER2 system uses approximately 38 percent less energy than a 10 SEER unit, and many qualify for the federal energy tax credit. KIC Refrigeration helps Irving homeowners evaluate repair versus replacement based on equipment age, repair history, refrigerant type, and projected energy savings.
Most AC repairs in Irving are completed in 1 to 2 hours during a single service visit. Capacitor and contactor replacements are quick fixes that take 15 to 30 minutes of hands-on time. Fan motor and blower motor replacements take 1 to 2 hours including wiring and testing. Compressor replacement is the most time-intensive repair at 3 to 6 hours because it requires refrigerant recovery with an EPA-certified machine, compressor removal, new compressor installation, nitrogen-purged brazing, pressure testing at 300 PSI, evacuation to below 500 microns, and recharging by weight. KIC Refrigeration arrives at your Irving home with a fully stocked truck to complete most repairs in a single visit.
KIC Refrigeration repairs every major air conditioning brand installed in Irving homes and commercial properties — Carrier, Trane, Lennox, Rheem, Goodman, Daikin, York, Bryant, Amana, Ruud, Heil, and all other manufacturers. Our technicians hold EPA Section 608 Universal certification for refrigerant handling and are trained to work with R-410A, R-22, R-32, R-454B, and all other regulated refrigerants found in residential and light commercial systems. Whether your AC is a 2-ton window package unit or a 5-ton split system, a 20-year-old R-22 unit or a brand-new inverter model, KIC Refrigeration has the diagnostic capability and parts access to repair it correctly at your Irving property.
Hear from property owners who chose us for their heating and cooling needs.
"KIC Refrigeration installed a new furnace for us last winter. The team was respectful of our home, wore boot covers, and cleaned up everything. Top notch."
"KIC Refrigeration did a full HVAC inspection before we closed on our new house. Very detailed report and the inspector answered all my questions patiently."
"HVAC inspection was very thorough. Got a written report with photos and recommendations prioritized by urgency. Helpful for budgeting repairs."